Supershieldz (2 Pack) Designed for OnePlus 10 Pro Tempered Glass Screen Protector, (Full Cover) (3D Curved Glass) Anti Scratch, Bubble Free (Black)

I love tempered glass protectors. The protector smashes when the screen normally would. My phones have lasted ten times longer since I started using these

The problem with these screen protectors is that they only affix on the sides or rails of phone. Even though they fit pretty well, there is small air gap in between screen and cover.This results in two problems. First, the touch sensitivity is not as good as full sticky covers. Especially at bottom and top. I feel like I'm pressing way too hard to get responses.Second, dust sneaks in the bottom and top over time from the environment and it's nearly impossible to get out.Solution? Apply adhesive to full perimeter of cover or, better yet, the entire area of cover like all the others.

Installation is a breeze, super easy. Unfortunately, once installed the touchscreen no longer functions reliably. I tried both screens sent to me and both had the same response. Touches in the middle of the screen are about 60% reliable on first touch. Touches on the edge of the screen are about 20% reliable on first touch. Fingerprint reader never works at first touch, I have to press hard and hope and then 50% of the time it works, the rest I have to punch in my lock code which often then takes multiple tries due to the touches not registering. Love the look and installation, but use is no good.

The product fits the phone nicely and goes on easily. I do agree with most of the reviews on here that the only downside is the crappy touch sensitivity. If I don't shatter this screen protector by dropping the phone, it will be from repeatedly pressing with no response.

It's really funny saying all these reviews saying that the touch sensitivity is bad or that the screen falls off or that it's just generally not a good product and I have not found that to be a case. within the first week of me getting my phone as well as my screen protector in case, my phone was ran over by a bus and the screen survived. The back part didn't, the screen was perfectly in tact.To be honest, I don't mind losing a bit of touch sensitivity, if my screen stays nice.To be fair, I am on my fourth on. They don't crack easy, but when they do, they spider out.They are better than any other solution out there.

Likes: seems to be very durable, easy to install no bubbles at allDislike: harder to touch things on the end of the screen. Curve doesn't seem to match and there are lines showing now.

I was hesitant to buy this screen protector because of all the bad reviews and overall rating. It is amazing so far and no problems with the fingerprint reader. I actually bought one of the top rated screen protectors from Amazon as my first screen protector purchase and it was a horrible screen protector. The only part of the protector that stuck to the phone was the perimeter and it popped off the moment my phone fell on the ground. I had problems with the screen reacting to my touch too because there wasn't a full seal. Don't be scared of the bad reviews. Buy this screen protector.

Got this for my oneplus 10 pro after the factory installed screen protector did it's job and saved my screen when something got dropped on it. Was I ever wrong.Used the alcohol wipe to clean the screen of fingerprints, oils and anything left over from the previous protector. Waited for it to sufficiently dry, wiped it down with the included cloths, ensured all dust was gone from the screen before installing the tempered glass protector... Followed the instructions perfectly... first one kept sliding around on the phone, wouldn't sit still, fell off in less than an hour and shattered when it hit the ground.Okay, there's two in the box, no big deal, maybe the phone wasn't dry? Maybe I didn't press it on firmly enough? Went through the entire process again with the second one. It stuck in place at least so I thought I was fine... Fingerprint scanner wasn't working at first, okay that's not unexpected with the swap in materials so I turned up the sensitivity on it and got it mostly working... Over the next few days it started getting worse. I could hear the clicking of the protector against the screen when I attempted to type or use the scanner telling me it was slowly lifting away from my phone.... Today it finally fell off.So, buyer, beware. If you can actually get it to stick to your phone, it would probably be a great protector for it, but good luck, because I really wasn't able to and ended up wasting $11 on something that's ending up in the trash.